How To - Cheap rear main/thrust cap puller

Forum rules
All advice given here is advice from persons using these forums,these opinions are not of the websites owners,and must be used at own discretion.
nwdatsuns does not verify the accuracy of given advice

This section is for informational How to's
Including, how to on datsuns, general technical, fabrication, electrical etc. Not limited to those, but for real information.
The how to make eggs and sammiches should go under General Discussion, as those topics aren't indexed for searches.
User avatar
BLUE
Posts: 1220
Joined: Wed Jun 26, 2013 6:48 pm
Cars: (3) s30's , (2) s130's
Location: NW Oregon

How To - Cheap rear main/thrust cap puller

Postby BLUE » Sun Sep 28, 2014 9:52 pm

Budget - rear main/thrust cap puller

In this How-To we'll be making a cheap dirty budget rear-main , and thrust bearing cap puller.

Required Materials
*Welder (arc/mig)
*Grinder with cut off wheel/Metal chop saw
*Drill press or drill w/drill bits.
*Safety glasses.
*Work Gloves.
*Scrap 3/16-1/4 bar stock (about 1ft will do).
*5ft of 1-inch or 3/4 square mild steel tubing.

(STEP 1) --- Building a trianglur shape to be able to bolt to the rear main , and thrust bearing caps (they are pre-threaded for this). The piece with the hole drilled in the center is what we'll be using.

Image007 by 71240z, on Flickr

Image008 by 71240z, on Flickr

Image010 by 71240z, on Flickr

A 9/32nd's bit was used I believe (it's been a while).

(STEP 2) --- Weld it all together like the picture below , and bolt it to the main cap.

Image020 by 71240z, on Flickr

Image022 by 71240z, on Flickr

Image028 by 71240z, on Flickr

Image014 by 71240z, on Flickr

(STEP 3) --- Cut (3) pieces of (1.5ft sections) of the 1-inch or 3/4-inch square tubing , and place (2) of the pieces on the block like in the picture below.

Image016 by 71240z, on Flickr

(STEP 4) --- Lay the 3rd piece that was cut in step 3 on the block like the picture below.

Image017 by 71240z, on Flickr

(STEP 5) --- Rear main cap pulling. This requires stacking (2) of the square tubes in the front braced across the block (like the picture below)) , and the third in the rear (like the picture below) , and finally sticking a pry bar through the center while lifting up to pull the cap.

Image031 by 71240z, on Flickr

Image032 by 71240z, on Flickr
DRIVEN » Sat Oct 11, 2014 10:24 am wrote:
1. Make progress until broke.
2. Go make mo money.
3. Repeat.
User avatar
DRIVEN
Posts: 5589
Joined: Thu Jun 27, 2013 7:05 pm
Location: I've been everywhere

Re: How To - Cheap rear main/thrust cap puller

Postby DRIVEN » Mon Sep 29, 2014 5:51 am

Crafty! Great option if you don't have access to a slide hammer.
When the only tool you have is a hammer every problem starts to look like a hippy.
User avatar
Laecaon
Site Admin
Posts: 3967
Joined: Wed Jun 26, 2013 7:21 pm
Cars: '71 510 Wagon, 02 BMW 325i Wagon
Location: PDX, West side.

Re: How To - Cheap rear main/thrust cap puller

Postby Laecaon » Mon Sep 29, 2014 11:34 am

I used a regular framing hammer, and a bar. Put a bolt in the cap, hook the hammers claw in the bolt, rest the head of the hammer on a bar like above, and pull on the handle.

Return to “How To”

Who is online

Users browsing this forum: No registered users and 2 guests