♦♦♦♦Dat's LZ Venti Deux♦♦♦♦

[KamikazeGarage]

Posted 02 August 2012 - 06:08 PM
Put 500ish miles on it!!

[KamikazeGarage]

Posted 18 August 2012 - 07:36 PM
Today I went to Lathrop to pick up precious cargo, to see a Bluebird and ultimately just say hi to a old friend of my dads.
The precious cargo was a fuel sending unit given to me from Gino (AKA Datsloco) Gino, if you read this, thanks a million again for the unit!

I gave the bitch vinegar, bitches love vinegar.


took her apart, cleaned contacts as best I can.


Thought this looked cool, didn't to it on purpose



Cleaned up pretty good :thumbup:




Again, Thanks a million for that piece Gino, Seeing those dimes was awesome as well. B)

[KamikazeGarage]

Posted 10 October 2012 - 05:46 PM

[KamikazeGarage]

Posted 20 October 2012 - 09:35 AM
It's true...
I got rearended.
I was pulling out of the parking lot, car died because the motor was still cold, idiot behind me in a ranger floored it.
Pulled over and started crying. not like a bitch but a silently stare and cry. lol. This car is my life.
Why I didn't bash his head in, I don't know. I have pretty good control of myself.
My friends are really sad too. They love this car haha. All the while the stupid fuck was bragging how he doesn't have a single dent on his ranger.
I really don't know why I didn't smash his face.

[KamikazeGarage]

Posted 02 November 2012 - 04:15 PM
So....
I got $4k from the insurance....
WTF.
WHAT THE FUCKING FUCK.
$4K.
No catches, no gimmicks, straight $4k. holy shit. car IS NOT SALVAGED. FUCK YES.

[KamikazeGarage]

Posted 25 December 2012 - 10:13 PM
Home for the holidays.




Also, person that "Fixed" my car did a shitty job.
But i'll live with it for now, just because I don't want to put up with another month and a half of his shit.
I'll drive her around for a while, on sunny days.

The driver side vs pass side.
The area above the tail light is supposed to be flat, not rolled like the passenger side.
I'm just going to buy a whole new panel and replace it.

[KamikazeGarage]

Posted 11 January 2013 - 10:07 PM

I cut off a filler neck from a newer car, and im trying to retrofit it to my 510. So far, everything went smooth. I forgot to take pics of the final product, but I need fuel safe hose to join the steel pipe to the gas tank.


ZX wheels are growing on me


I tacked them bitches in with the gas tank full



All done
:thumbup: :thumbup:



Culprit





Look Ma, no hands!!

[KamikazeGarage]

Posted 22 March 2013 - 07:13 PM

[KamikazeGarage]

Posted 30 September 2013 - 10:47 PM

Lets just say i was in a coma.
Officially a LZ22.
(camera is broken)
L20B Head Gasket on a Z22E, D81 block. WILL NOT WORK. I used Z22E gasket, from a normal Z22 block.


Drilled holes in block (NERVE RACKING HOLY SHIT)


Port matched the intake/head ports and smoothed the transition.


Assembled!

[KamikazeGarage]

Posted 01 October 2013 - 10:36 PM
Right so, everything was going smoothly until I picked up the MIG gun. I suddenly forgot how to weld, or today was just not my day. I WAS going to cut and tweak the tube that goes from the lower block to the PCV but that all went to hell after I blew a hole into the tube. No matter, I can fix that still.
The current problem is that I cant seem to find a Manual brake pedal around here, so i'm going to cut my Auto one so it fits. I dont see why it wouldnt work, for now at least.
I finished assembling my engine completely today, worked till 9.
Things accomplished today:
Pulled auto tranny, and driveline. Seems the "Shortened driveline" I bought a while ago was stock. lol.
took apart pedal assembly. I concluded that there is no way in hell im going to take out the whole box
mounted clutch master, got a general idea of the routing.
Things to do still:
Fab tube from crankcase to PCV.
Fab Tranny crossmember
Shorten driveline
Fit auto brake pedal
Bend clutch lines
START HER UP!!
I pulled the engine out of my 510 last week Tuesday, and thats when this swap started really.
I would have gotten to it earlier but the dude that did my paint said he'd buff the car in the same day, and here we are.. two years later.

Also I'd like to point out that my old L20B was pretty worn. Glazed cylinders, sludgy crankcase, and worst of all it was running pretty lean (Thanks to Mr. "I can tune a carb" over here)
Add to that an exhaust leak and a tiny intake.. it now makes sense why it didnt have much power, but at the same time it did.. I mean I could swing donuts no problem, and pull on a old farm truck F100 lol. If I was getting 80hp to the wheels at best..

I'm even more anxious to see what this fresh LZ has in store.. though I think the 32/36 might be a tad too small for it.

[KamikazeGarage]

Posted 05 October 2013 - 06:39 PM

Much progress today.
Should hook up exhaust and intake mani tomorrow, and measure required driveshaft length (280zx FS5W71B.) as well cut the hole for the shifter.
I ordered a 280sx transmission mount, it should be here on Tuesday, that'll be the same day I figure out the tranny crossmember.
My deadline to get it driving is Friday at the latest. I have a swap meet to attend on Saturday, im hoping to make it in the 510.
if not i'll tow it over there.

[KamikazeGarage]

Posted 08 October 2013 - 06:19 PM
Started her up today!
Problem.
Exhaust leak under the 2 center exhaust ports.
Smoke, wierd smell too.
Car wont stay running.
Ill readjust carb.

[KamikazeGarage]

Posted 09 October 2013 - 06:19 PM
Transmission Crossmember fabricated and installed today! All systems go!

Need to make minor adjustments to carb and she should be road worthy!
All aforementioned problems are fixed! Smoke and wierd smell were due to solvents used to clean deck surfaces, or Gaskets seating? No more smoke or leaks.
Though i should look into advancing the dizzy/oil pump drive a tooth

[KamikazeGarage]

Posted 10 October 2013 - 04:55 PM

FIRST TIME ON THE ROAD IN A COUPLE WEEKS EVERYTHING SOUNDS WORKS AWESOME NO COMPLAINTS AHHHH OMG FINALLY A PROPERLY WORKING DATSUN ASSEMBLED BY ME I GUESS I KNOW WHAT IM DOING DISREGARD LACK OF PUNCTUATION IDGAF IM EXCITED AS FUCK I JUST GOT HOME FROM MY SHOP BEST DRIVE OF MY LIFE ROASTED TIRES THROUGH SECOND GEAR WITH A WHACK ASS WEBER I NEED SIDE DRAFTS WOOOOOOO TODAY MARKS THE FIRST DAY OF MANHOOD WOOT WOOT WOOT

[KamikazeGarage]

Posted 11 October 2013 - 06:38 PM

[KamikazeGarage]

Posted 21 October 2013 - 11:56 AM
Yeah so I was going to instal my "ZX" coilovers today but I ran into a bit of a problem
I got my 280zx rotor in the mail, look at this beautiful thing


Anxious, I run to the shop to install these things. but weighing them in my hand I notice that they are HUGE!
So I compare them to the "ZX" rotors

hmm wait hub looks a little weird


Wait they look like stock 510 struts
What the P/N on them


ok looking at the spindle..



FUCK.
FUCK.
I was hoping to pull my front wheels in, looks like thats not happening without camber plates. IDK about those brand new rotors either.

[KamikazeGarage]

Posted 22 October 2013 - 04:52 PM

L20B head gasket on KA24DE head.

I dont have a Z series gasket but im sure its closer than a L..
How cool does a KAZ22DE sound?
Here are my ideas thus far
Z22 block, L20B crank (fully balanced) IDK on rods or piston yet. I know the DE head has quite a big combustion chamber, so I either need high pin height pistons or boost to make up for lack of compression.
Dont tell me to start with a Z24 or KA, neither have balance cranks, nor have the ideal rod/bore ratio for high revs. Yes my goal is to achieve high revs, with or without boost. Im just not sure on the pistons speeds, C/R or Rod/Bore ratio I want. Or boost. Im aiming to use Nissan parts, but if I need to use different pistons and rods so be it. I dont plan on running lots of boost either. ~10psi, R1 carbs or EFI. Id need stand alone ECU because of the block head combo.

or I may just throw this whole idea out and hold out for a SR20VE. I just want a high revving sumbitch. and still streetable. The VE is perfect for this I think.

[KamikazeGarage]

Fave testament song before Formation of Damnation

[KamikazeGarage]

[KamikazeGarage]

*skanking*