Page 2 of 4

Re: 71 510 goon with ka24de

Posted: Fri Nov 08, 2013 3:12 pm
by 510freak
squatches wrote:
510freak wrote:Damn,Sure hope you mend so enough man.
You have a good therapy going for yourself
yea man cars are good therapy for anything, doesn't matter if im working on them, driving them or just looking at them Its always awesome!

510 is on jackstands now, awaiting the fuel lines ive already bent up the new 5/16 fuel lines. also working on putting z crossmember up under it, hopefully ill be getting some more sheet metal next week to finis the floor boards.
For sure

Keep up the good work man :thumbs:

Re: 71 510 goon with ka24de

Posted: Fri Nov 08, 2013 5:20 pm
by jayden71
:fuu: :fuu:

Glad u survived the wreck.

Nice progress on the goon!!

Re: 71 510 goon with ka24de

Posted: Wed Nov 13, 2013 4:55 pm
by squatches
went out and got some more sheet metal and gas for the welder to finish the floors, get a few spots tacked in and start to weld them in and the wire runs out. :fuu:

Re: 71 510 goon with ka24de

Posted: Mon Nov 18, 2013 4:27 pm
by squatches
picked up some battery wire to relocate the battery, terminal ends, a new slave cylinder, 5/16 fuel hose, and some new bolts for the drive shaft. finally getting some shit done. :fyea:

Re: 71 510 goon with ka24de

Posted: Mon Nov 18, 2013 4:29 pm
by 510freak
:fyea:

Keep up the great progress

Re: 71 510 goon with ka24de

Posted: Mon Nov 18, 2013 10:29 pm
by squatches
got the drive shaft, clutch master and slave in, put the fuel lines in now to finish the fuel tank. i would take pics but my camera crapped out on me, it seems all my electronics have decided to take a shit on me this month.. :fa:

Re: 71 510 goon with ka24de

Posted: Tue Nov 19, 2013 12:00 pm
by izzo
well wipe their ass n tell em get back to work :| Lolz.

Re: 71 510 goon with ka24de

Posted: Tue Nov 19, 2013 1:59 pm
by squatches
izzo wrote:well wipe their ass n tell em get back to work :| Lolz.
i wish it were that simple, just wipe, powder their ass, and yell a them for shitting.. its probably a good thing i cant have kids haha. :lol:

Re: 71 510 goon with ka24de

Posted: Tue Nov 19, 2013 4:58 pm
by BLUE
squatches wrote:got the drive shaft, clutch master and slave in, put the fuel lines in now to finish the fuel tank. i would take pics but my camera crapped out on me, it seems all my electronics have decided to take a shit on me this month.. :fa:
:fuu:

tis ok ... I can visualize fapping to it until ... you get the $54 dorra Kodak camera off Amazon

:fry:

Re: 71 510 goon with ka24de

Posted: Tue Nov 19, 2013 10:15 pm
by squatches
BLUE wrote:
squatches wrote:got the drive shaft, clutch master and slave in, put the fuel lines in now to finish the fuel tank. i would take pics but my camera crapped out on me, it seems all my electronics have decided to take a shit on me this month.. :fa:
:fuu:

tis ok ... I can visualize fapping to it until ... you get the $54 dorra Kodak camera off Amazon

:fry:
don't forget to stretch first don't wanna pull something... :P i will have to look into one of those after i get a few more parts for wagon.

Re: 71 510 goon with ka24de

Posted: Tue Nov 19, 2013 10:57 pm
by squatches
I umm.. borrowed my gf's phone when i left her house lol, maybe she hasn't noticed i have it yet.. but bled out the brakes and took some pics tonight.

new clutch master.

Image

new slave.

Image

my blue shaft in and bolted up..

Image

hard lines temporarily in.

Image

Image

soft lines to engine.

Image

put the radiator back in.

Image

battery will be going here, going to build a box where the seats used to be. need to get an agm battery to.

Image

metal for the floors.

Image

pulled this off a maxima in pap.

Image

started pulling shit back apart... i cant leave stuff alone, the original speedo was broke.

Image


Image

510 speed gauge compared to 240s

Image

240 cluster apart.

Image

Image

Image

240 gauge face didn't fit well at all..

Image

so i took the 510 gauge face and notched the screw holes a little.

Image

240 speedo inside mounted to 510 gauge face.

Image

Image

Image

the 240 needle hit the 510 gauge housing, needles compared.

Image

with 510 needle.

Image

its sitting a little sideways because it hits where the screw goes in, ill hit it with the dremel later.

Image

Image

Re: 71 510 goon with ka24de

Posted: Tue Nov 19, 2013 11:02 pm
by izzo
Dude!! Thats pretty awesome man. Good job

Re: 71 510 goon with ka24de

Posted: Wed Nov 20, 2013 1:00 am
by squatches
izzo wrote:Dude!! Thats pretty awesome man. Good job
thanks! hopefully tomorrow ill have some time to grind that little bit out and wire the speedo up. then I have to figure out how to hold it in, the old gauge was bolted to the backing of the cluster.

Re: 71 510 goon with ka24de

Posted: Thu Nov 21, 2013 7:12 pm
by squatches
yesterday I ground the screw tower that was blocking the speedo from sitting straight, now it sits flush and straight like its supposed to and you cant tell its been messed with besides the odometer not being there.

piece that needed grinding.

Image

no brackets needed to hold it either it sits snug and holds its self.

Image

now ive got to figure out where to put this, ill have to extend the wires and put it some where in the dash.

Image

also fixed the reverse lights so they worked on the 240 trans, next ill wire up the 240 speedo should be fairly simple.

Re: 71 510 goon with ka24de

Posted: Fri Nov 29, 2013 1:29 pm
by squatches
finally got around to bending up the sheet metal for part of the floor patch, its not the best but all i had to bend it was the 2x4's in the wall and a hammer.

Image

Image

ignore the mess of wires not done under the dash yet got to get a soldering gun lol.

Image

Re: 71 510 goon with ka24de

Posted: Sat Nov 30, 2013 11:26 am
by izzo
Floor pans. Cool add on :rofl:

Re: 71 510 goon with ka24de

Posted: Sat Nov 30, 2013 12:50 pm
by squatches
izzo wrote:Floor pans. Cool add on :rofl:
how much hp you think its good for? :fu: :rofl:

Re: 71 510 goon with ka24de

Posted: Mon Dec 02, 2013 11:59 pm
by squatches
motor mounts came in today! got trans cross member made, all thats left to actually drive it is fuel pump. ive got so many boners now! lol

Re: 71 510 goon with ka24de

Posted: Tue Dec 03, 2013 12:57 am
by squatches
i was so happy to see this on my porch this afternoon.


Image

Image

Image

installed.

Image

Image

trans crossmember in, the long bolt is in there for getting everything lined up i couldnt find another bolt that would fit lol.

Image

out for paint and awaiting bolts.

Image

and my company while under the car.

Image

Re: 71 510 goon with ka24de

Posted: Tue Dec 10, 2013 5:03 pm
by squatches
put in the clutch line last night and almost finished patching all of the passenger side floor board.

thsi is some of what i cut out, well half way cut out... :|

Image

Image

still have to more holes to go.

Image