Re: The never ending Project(s)
Posted: Tue Nov 21, 2017 7:31 am
nice 510, does it have the L or Z engine ?izzo wrote:
Page 26 of 27
Re: The never ending Project(s)
Posted: Tue Nov 21, 2017 9:13 am
Re: The never ending Project(s)
Posted: Tue Nov 21, 2017 10:07 am
Re: The never ending Project(s)
Posted: Tue Nov 21, 2017 10:38 am
OK guys, I F'd up and called the 210 a 510. Still a Datsun,eh .....
i'm old, give the old man a little break. pleze.
Re: The never ending Project(s)
Posted: Tue Nov 21, 2017 11:18 am
We have. For months.
Welcome back.
Welcome back.
Re: The never ending Project(s)
Posted: Tue Nov 21, 2017 3:46 pm
months ? better not push my luck then.DRIVEN wrote:We have. For months.
Welcome back.
thanks for the welcome back, very much appreciated.
Re: The never ending Project(s)
Posted: Sun Nov 26, 2017 7:05 pm
Hahaha
It's an odd one. Someone done stuck an A series in ma 510.
Lolol
It's an odd one. Someone done stuck an A series in ma 510.
LololRe: The never ending Project(s)
Posted: Sun Nov 26, 2017 7:10 pm
Started tearing down the front end
Got side tracked and installed a good set of struts. Springs were cut. Lowered it a little.
Will be getting another complete set. Going to cut the lower perch on those and move it down roughly two inches
Got side tracked and installed a good set of struts. Springs were cut. Lowered it a little.
Will be getting another complete set. Going to cut the lower perch on those and move it down roughly two inches
Re: The never ending Project(s)
Posted: Tue Jan 09, 2018 8:16 pm
Got a few new fuel pump spacers. Need to get some brake hoses for the old girl. These are cracked and falling apart, oh noes!
(for the 77)
(for the 77)
Re: The never ending Project(s)
Posted: Wed Jan 10, 2018 4:30 am
Safety first.
Re: The never ending Project(s)
Posted: Wed Jan 10, 2018 2:47 pm
Lolol. Not today, bro!
Rip shit tear ass, im ready to dump the clutch n punch the gas!
Rip shit tear ass, im ready to dump the clutch n punch the gas!
Re: The never ending Project(s)
Posted: Wed Jan 10, 2018 9:29 pm
Thread needs more wheelies
Re: The never ending Project(s)
Posted: Sun Jan 14, 2018 3:07 pm
Well, that maybe possible soon.
Got a brand new fuel pump on the 77 hatchback. She runs again. Running the wifes stocker carb on it. It needs to go the fuck away and I want a weber or 1200 carb.
my red 79 has some slight issues when driving. There is always a miss off idle, plus a dip while foot just barely on throttle. It feels vacuum leakish. So saturday, I sprayed some starting fluid around to try and find it. Sprayed the base of the carb, and idle changed. Pulled the carb off, and someone decided to use RTV for a fucking gasket because the carb spacer has a small crack in it. I cleaned it all up, made new gaskets out of gasket paper. It's slightly better, but I really need a weber on the thing or a different carb. Tired of dicking with this old stocker.
Also scored these
Got a brand new fuel pump on the 77 hatchback. She runs again. Running the wifes stocker carb on it. It needs to go the fuck away and I want a weber or 1200 carb.
my red 79 has some slight issues when driving. There is always a miss off idle, plus a dip while foot just barely on throttle. It feels vacuum leakish. So saturday, I sprayed some starting fluid around to try and find it. Sprayed the base of the carb, and idle changed. Pulled the carb off, and someone decided to use RTV for a fucking gasket because the carb spacer has a small crack in it. I cleaned it all up, made new gaskets out of gasket paper. It's slightly better, but I really need a weber on the thing or a different carb. Tired of dicking with this old stocker.
Also scored these
Re: The never ending Project(s)
Posted: Sun Jan 14, 2018 4:43 pm
4x4 conversion in store for the B?
Re: The never ending Project(s)
Posted: Wed Jan 17, 2018 7:50 pm
Haha shit....
Just got hooked up with those for helping find a part for someone. Found it and they insisted on giving me them. so there we have it lol
Just got hooked up with those for helping find a part for someone. Found it and they insisted on giving me them. so there we have it lol
Re: The never ending Project(s)
Posted: Wed Jan 17, 2018 7:57 pm
Sweet deal!
Re: The never ending Project(s)
Posted: Thu Jan 18, 2018 7:56 am
I had those same wheels on a hardbody I owned. They shine up nicely for sure.
Re: The never ending Project(s)
Posted: Thu Jan 18, 2018 8:18 pm
What size?
Re: The never ending Project(s)
Posted: Mon Jan 22, 2018 9:48 pm
Not sure what size they are.
But... As always, something new arrived.
But... As always, something new arrived.
Re: The never ending Project(s)
Posted: Mon Jan 22, 2018 10:21 pm
I was given this truck. I have to install a trans into a 720 king cab. Small price to pay
This was a custom truck at one point obviously. Canopy has a seal and there is no back window. Custom paint. I like the patina. I am using Norton polish to preserve it. It cleans up. Polishes. And gets in deep like glaze. Not hard to do. Won't take too much time.
I tried stuffing the trans into the truck from the bottom but am not strong enough. So motor is coming out. This truck is also an AC truck. So lots of stuff to carefully remove. Keeping the AC and don't want to breathe r12 so carefully just taking the pump off the block and working around it. I'll get the motor out, replace the front and rear main seal, oil pan gasket. Mate the trans and stuff it back in.
This was a custom truck at one point obviously. Canopy has a seal and there is no back window. Custom paint. I like the patina. I am using Norton polish to preserve it. It cleans up. Polishes. And gets in deep like glaze. Not hard to do. Won't take too much time.
I tried stuffing the trans into the truck from the bottom but am not strong enough. So motor is coming out. This truck is also an AC truck. So lots of stuff to carefully remove. Keeping the AC and don't want to breathe r12 so carefully just taking the pump off the block and working around it. I'll get the motor out, replace the front and rear main seal, oil pan gasket. Mate the trans and stuff it back in.