DONT DO THIS.
soon to be LZ2.3 521 :)
-
wayno
- Posts: 5321
- Joined: Thu Jun 27, 2013 8:44 pm
- Location: Vancouver WA
- Has thanked: 432 times
- Been thanked: 1302 times
Re: soon to be LZ2.3 521 :)
It's a bitch getting in there the wrong way. 
“The difference between genius and stupidly is that genius has its limits” Albert Einstein
Re: soon to be LZ2.3 521 :)
I'll be making the 521 my new job tomorrow...
today was the last day of work at the wash.
today was the last day of work at the wash.
-
DRIVEN
- Posts: 7699
- Joined: Thu Jun 27, 2013 7:05 pm
- Location: I've been everywhere
- Has thanked: 1210 times
- Been thanked: 1180 times
Re: soon to be LZ2.3 521 :)
Make shit happen!
When the only tool you have is a hammer every problem starts to look like a hippy.
Re: soon to be LZ2.3 521 :)
I got it in and lubed up.. tomorrow I'll be doing the other side. Also got the exhaust and Sus bolted on.
I wasn't home very long but I feel I got a lot done. Oh flatcat I've got you down pipe waiting to bring over. Chris must not wanna touch his datto unless it's at his house or something. I never can get a hold of him. I'll push him harder! That fuck needs to fix his datto.
Oil cooler has got oil in it, I will put oil in the block tomorrow. I'm waiting on ngk wires. The order I placed online for some wires was dropped for some reason... I think do to my new debit card but I don't have any and I called around and can't get any. Napa couldn't at least. I'll place another order. Amazon had them I'll get them from there.
-
flatcat19
- Posts: 5233
- Joined: Thu Jun 27, 2013 11:53 am
- Title: AKA Smoke
- Cars: Smaller. Better. Slower. Lower.
- Location: Where you aren't.
- Has thanked: 12 times
- Been thanked: 32 times
Re: soon to be LZ2.3 521 :)
If you have an old set you can take them to Baxter's and they will cut you a set of MSD wires on the spot.
At least all the Baxter's shops in Portland did that.
At least all the Baxter's shops in Portland did that.
-
DRIVEN
- Posts: 7699
- Joined: Thu Jun 27, 2013 7:05 pm
- Location: I've been everywhere
- Has thanked: 1210 times
- Been thanked: 1180 times
Re: soon to be LZ2.3 521 :)
You gonna have this thing running before you get 50 pages?
When the only tool you have is a hammer every problem starts to look like a hippy.
-
Laecaon
- Site Admin
- Posts: 4793
- Joined: Wed Jun 26, 2013 7:21 pm
- Cars: '71 510 Wagon, 02 BMW 325i Wagon
- Location: PDX, West side.
- Has thanked: 288 times
- Been thanked: 329 times
Re: soon to be LZ2.3 521 :)
What? I have never heard of that...flatcat19 » Fri Aug 29, 2014 11:31 am wrote:If you have an old set you can take them to Baxter's and they will cut you a set of MSD wires on the spot.
At least all the Baxter's shops in Portland did that.
-
flatcat19
- Posts: 5233
- Joined: Thu Jun 27, 2013 11:53 am
- Title: AKA Smoke
- Cars: Smaller. Better. Slower. Lower.
- Location: Where you aren't.
- Has thanked: 12 times
- Been thanked: 32 times
Re: soon to be LZ2.3 521 :)
Over the years I have had many sets made there.
Milwaukie, Beaverton, Tigard, Vancouver.
If they didn't have goofy plug ends(Honda, Toyota, Nissan) no problems.
Milwaukie, Beaverton, Tigard, Vancouver.
If they didn't have goofy plug ends(Honda, Toyota, Nissan) no problems.
Re: soon to be LZ2.3 521 :)
Small leak is an even smaller leak now. Oh also THE BITCH STARTED!!
I know I have a small down tube gasket problem so I'll be fixing that and getting the thermostat gasket shit figured out maybe the housing is all jacked up and I didn't notice.. I'll see what I can do about a video
exhaust system isn't hooked up. Also gotta bang out a u joint and fit the 720 slip yoke onto the 520 one piece.. never done one...
Oh and baxters here doesn't do that flatcat.
Well the dude I talked to sounded fucking clueless to what I was talking about.. I picked up some cheapo ones for the time being. NGKS should be on the way this time.
I know I have a small down tube gasket problem so I'll be fixing that and getting the thermostat gasket shit figured out maybe the housing is all jacked up and I didn't notice.. I'll see what I can do about a video
exhaust system isn't hooked up. Also gotta bang out a u joint and fit the 720 slip yoke onto the 520 one piece.. never done one...
Oh and baxters here doesn't do that flatcat.
Well the dude I talked to sounded fucking clueless to what I was talking about.. I picked up some cheapo ones for the time being. NGKS should be on the way this time.
Re: soon to be LZ2.3 521 :)
Today I hammered out the ujoint to put the 720 slip yoke onto the 520 one piece. Since the ujoint is bran new, I just reused the one I had put on a few week back at a shop. Ha. However i bent one of the U clips so I'll be getting a new ujoint. Haha